Road repairing use movable Temporary traffic signal light

road repairing use movable Temporary traffic signal light description::
Product model: WDM-YD200-04-RYG
1. Lamp head size: 100*250*155MM
2. Bottom box size: 800*550*400MM
3. Total height: 2360MM
4. Lamp beads category: Taiwan Epistar chip lamp beads
5. Red wavelength: 620-625NM
6. Green wavelength: 500-505NM (blue-green)
520-525NM (Emerald)
7. Yellow wavelength: 590-595NM

8. Lamp color: red yellow green

9. Number of lamp beads: 50 for red, yellow and green, 70 for red and green
10. Shell material: electrostatic spraying, sheet metal chassis
11. Working temperature: -40C°~65C°
12. Protection grade: IP65
13. Solar panel: 30W/50W/60W/ 18V
14. Battery: 12V/55AH
15. Working mode: remote control or manual control
200 type solar mobile traffic light
Type 200 mobile traffic light is mainly used for traffic intersections. It is a movable solar emergency traffic light, which is powered by solar energy and has a light source.
The use of high-quality LED energy-saving light sources is suitable for intersections, without the need for cable connections, that is, no broken roads or overhead lines are required, installation is very simple, time-saving, labor-saving and cost-saving, easy maintenance, emergency command in case of power failure or repair of traffic lights Vehicles and pedestrians pass; its mobility is very strong, you can move the signal light arbitrarily, placed at various intersections of emergency needs.

Technical solutions of road repairing use movable Temporary traffic signal light:
1. The lamp beads of solar mobile communication traffic lights are all made of condensing LEDs. Its LEDs are all 5MM round head lamp beads, because the round head lamp beads belong to the condensing type LED, and the round head lamp beads are on the top The colloid is relatively high, and the colloid forms a light-gathering effect. This LED is basically used for traffic signal indicator lights. Our 200-type solar mobile lights are also made of this LED.
2. The housing of solar mobile communication traffic light is an environmentally friendly plastic shell, which is characterized by good chemical stability, good corrosion resistance to general acids and alkalis; good electrical insulation, which is a poor conductor and safe to use; It has good waterproof performance and is durable. The car is made of sheet metal, and the sheet metal chassis is made of cold-rolled sheet. The cold-rolled sheet has good surface quality, non-reflective and anti-glare. It is fully enclosed, all-weather, weatherproof, and has good oxidation resistance. Does not fade.
3. Reflective lens is installed on the solar mobile communication traffic light. Because solar mobile traffic lights are powered by solar energy, it is necessary to do as much supply as possible to ensure that it works properly. This is the commonality of solar products. In order to make the brightness of the entire moving traffic light higher under the same current situation, a retro-reflective lens must be installed. Under the same current situation, a retro-reflective lens should be installed to increase the brightness several times.
4. Solar mobile communication traffic light solar panel, solar mobile traffic light solar panel is made of single crystal silicon material, is a relatively active non-metallic element, with high purity and high efficiency solar energy conversion rate, and most of the use of amorphous silicon Compared with polysilicon products, monocrystalline silicon solar panels have superior battery life and high photoelectric conversion rate, which allows yellow flash lamps to work longer in continuous rainy weather.

road repairing use movable Temporary traffic signal light product display:

Installation method of road repairing use movable Temporary traffic signal light:
Solar panel installation:
1. Assemble the solar panel and solar bracket and tighten the screws;
2. Install the solar panel with the bracket installed on the bevel bracket and tighten with screws.
Light box installation method:
1. Install the sun visor on the upper part of the lamp, put the sun visor on the lamp, and tighten the screw to the corresponding hole position;

2. Leave a screw on both ends, unscrew the nut above the screw, Punch 2 holes on the signal light pole, drill holes according to the signal L-bracket position, use a suitable screw to pass through the light pole, and insert the L-shaped bracket Put on the screw and fix it with the nut.

Light pole and trolley installation:
1. Install the installed solar panel and light box on the light pole in sequence, and the wire passes through the light pole;
2. The solar panel is installed on the top of the light pole lamp, and the hole position of the bevel bracket is aligned with the hole position of the upper end of the light pole and fixed with screws;
3. Drill holes according to the position of the L-bracket of the signal, use a suitable screw to pass through the lamp post, and put the L-bracket on the screw and fix it with the nut.
4. Align the holes on the flange at the bottom of the pole where the solar panel and the lamp are installed with the holes on the trolley, and then fasten with M12 screw + shrapnel + gasket. (The screw is covered with shrapnel first, then the gasket)

In addition to road repairing use movable Temporary traffic signal light, We also produces Other traffic lights:
1. Motorized traffic lights
2. Direction traffic lights
3. Mobile traffic lights

4. Integrated traffic lights, etc.

Contact us if you need more details on Temporary Traffic Light. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Movable Traffic Signal Light、Mobile Traffic Lights. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Traffic Light > Solar Traffic Light